Questions

How to install filter in aquarium video

Pin
Send
Share
Send
Send


How to install and use aquarium filters

The aquarium filter performs a cleaning function, removing chemical and mechanical impurities from the water. In order for it to function correctly, it must be correctly placed in the tank. The life of all the inhabitants of the aquarium depends on his work.

How to put internal filters?

Internal filters are installed inside the aquarium. The most popular - internal pump filters and airlift. They are inexpensive, they are easy to install yourself, they are convenient to use during operation. However, these mechanisms have their drawbacks - they must be cleaned of dirt almost every day, they are overall and noisy. Before purchasing such a water purifier, determine whether it fits in your tank.

Will it be possible to install the internal filter correctly the first time? Completely if you carefully read the instructions. The device must be placed in the tank when it is half filled with water, when there are plants planted in the soil. Before turning on the filter in the network, it should be assembled in parts, and mounted on the wall or above the aquarium.

Water purification devices such as internal filters should be completely immersed in the aquatic environment. Above the filter should be another 3 cm of water. The device itself should not touch the bottom. If you bought an internal filter, or made it yourself, then attach it correctly using suction cups to the glass wall.

See how to disassemble, assemble and install the internal filter.

Included with the branded filter is a hose for air supply. In the homemade device, it should also be present, however, the principle of attachment is the same. Take one end of the tube and attach it to the special opening of the filter, the other end of it out above the water and fix it with the help of the fastened material to the upper edge of the tank wall. The tube must be above the water level, otherwise the air will not be properly sucked.

On the tube or directly on the filter should be an air supply regulator. Its location affects the flow of water in the aquarium. After installing the water purification device, the regulator should be correctly placed in the middle position. Then watch the behavior of the fish - some will love the flow of water, others will avoid it. Adjust the water flow level so that the fish feel comfortable.

Internal cleaners should be installed after they are completely immersed in water. Before you get it out of the water for cleaning, the device must be disconnected from the power supply. Also, do not leave the mechanism turned off in the water, and turn it on after a long period of stagnation (if you did not have time to clean it).

How to put external filters?

External filters are more bulky, and more expensive for the price. Despite the financial costs, these types of water purifiers have many advantages. The most important thing is fillers, which consist of filtering materials. Periodically they need to be replaced, which is quite simple to do.

See how to clean and replace the filler in the external filter.

External cleaners are not very noisy, they are suitable for spacious aquariums from 100 liters and more, they provide a biological method of water purification. In such an apparatus there may be several fillers: stones, sponge, rings, etc. Therefore, experienced craftsmen with the availability of skills make external filters with their own hands. The principle of operation of the external system of cleaning the reservoir: the aquarium water gradually pass through a special tank, in which there is a filler of filter materials. Then purified water flows back through the tube to the tank.

Clean this device is not difficult. The cleaning process should occur in the aquarium water itself, which must be drained into a separate container. Further filtering matter is gradually replaced. For example, a sponge cannot be replaced completely, but only a part of it. Cut off half of the old sponge and put a new one in its place. After a few days, useful bacteria multiply in it, and the biological environment will not be disturbed.

To install an external device for water treatment correctly, you need to read the instructions. If it is homemade, then it must first be assembled by placing all the fillers with sponges in their cells. It is also required to close both taps where the tubes are connected.

The device will be able to function properly if it is installed below the water level (20 cm). To the external filter are 2 tubes that take water and release it. They need to be fixed on opposite corners of the tank. When all parts are connected to a fully assembled device, it will need to be filled with aquarium water using a drain. Otherwise, the air from the tubes will not allow the device to function properly.

To release the air plugs, you must connect and open a hose that takes water. Wait for the filter to fill with water. Do not allow water to flow out of the hole for the second tube. After filling the unit, turn off the inlet hose.

After that, you need to connect a hose that releases water. To do this, turn off its valve, and water will accumulate in the hose. Only after these procedures can you connect it to the system of water intake from the tank. You can later open two taps and connect an external filter to the power supply. Only with the observance of all the rules of safety and operation, the mechanism will work as it should. Never turn on the machine if you notice mechanical damage on it. Be careful in working with aquarium equipment to ensure a comfortable life for fish and plants.

How to install the internal filter in the aquarium :: how long should the filter in the aquarium work :: Equipment and accessories

Tip 1: How to install an internal filter in the aquarium

For a man, one of the most placating spectacles is watching how fish swim. It calms the nerves and relaxes the body, and most importantly is pleasant to the eyes. But you need to not only watch them, but also take care of them. In particular, take care of the purity of the water.

Instruction

1. Find the right filter for your aquarium, a particular manufacturer. Thanks to the right choice, you will get rid of further problems with filters.

2. Consult with experts or vendors, they will help you choose the right filters, tell you how to properly care for the aquarium and its inhabitants, how to clean it, how to monitor the degree of contamination.

3. Buy an internal filter suitable for your tank. Unpack, read the instructions and try to install it according to the instructions in the aquarium. It must be filled with water. Remove all the fish from the aquarium, so that they do not interfere with the installation of the filter.

4. Immerse the internal filter in water, completely, so that from above it is covered with water to a depth of about ten to fifteen millimeters.

5. Attach to the walls of the aquarium internal filter. They usually have velcro, due to which they are attached to the walls of the aquarium. This will help to fix it at a certain level and not to move either way or the other.

6. Install the filter so that the tube to which the hose is attached exits. This will facilitate cleaning and give your fish a clean environment in which they will live. Through this tube the waste water comes out, which enters through a sponge located at the end of the filter tube.

7. Plug the filter into a power outlet so that it starts working. Do not forget about safety, including it, checking how it works.

8. Check if the internal filter is working on your tank. To do this, you need to bring your hand to the top outlet, if you feel the stream of water, then the filter is functioning as needed. Take a few minutes to see if it works correctly.

9. Put the fish in the aquarium and see if they are comfortable with the filter. If everything is in order and it works as it should, you can continue to enjoy your pets. The main thing do not forget to feed them and monitor the cleanliness of the aquarium. A clean environment will help them to extend the maximum life and, thereby, longer delight you.

Tip 2: How to install aquarium filter

If you decide to install an aquarium at home, then you cannot do without an aquarium. filter. His choice should be treated with special attention, since the quality of water in your underwater kingdom will depend on this device.

Instruction

1. Today, there are many varieties of aquarium filters: internal, external, bottom, aerator filters, as well as filters that produce mechanical filter(as filter used filter thread, sponge or crumb), chemical filter(using activated carbon or zeolite), as well as biofiltertion (microorganisms are used in the filter that purify water from harmful impurities).

2. The filter must be selected based on the volume of the aquarium, as well as the functions that it will have to perform. For example, external filters are easy to use, and bottom filters help create a more favorable microflora in the aquarium, and they need to be cleaned every two to three years. For small aquariums, an ideal option would be a filter aerator, which combines the functions of cleaning and saturating water with oxygen. In any case, before you choose any specific filter, you should consult with a specialist.

3. Before installing the filter, carefully read the instructions. If you purchased a chemical filter, you must fill it with the adsorbent that comes with it.

4. Before installation filter prepare an aquarium. Rinse it thoroughly and fill it with water to see if the seams are leaking. Drain and place pre-prepared soil on the bottom of the aquarium. If you purchased a bottom filter, you must first install it under the ground. Pour about one third of the water, then plant the plants. If you choose an internal filter, then you need to install it at this very moment. Attach the filter with special velcro or retaining bracket, then fill the aquarium with water to the required level. An external filter can be installed after filling the aquarium with water.

5. After filling the aquarium, turn on the filter in order to check its operation. While the aquarium will be balanced (about two weeks), the filter must be kept on. As soon as you see that the water has disappeared from the water, then you can safely inhabit your underwater world with fish.

note

When buying an aquarium, do not forget that in addition to appeasement from it, you will still take care of its inhabitants and their habitat, that is, an aquarium. Regularly keep it clean.

Installing an external filter in the aquarium

The question of installing an internal filter in an aquarium is puzzling all novice aquarists. It seems to be all very clear, but how to do everything right so that in no case nothing happens. Is it necessary to immerse the filter completely in water or not? Why this transparent tube? And after all, what is the most interesting instruction to filters is not always clear and detailed.

The internal filter is called because it is located directly inside the aquarium itself. The external filter is bulky and located outside the aquarium. Installing an external filter in the aquarium is not too complicated process.

The internal filter is located in the water so that there is still 3 cm of water above its level. Such a device is attached to the wall of the aquarium with the help of suction cups, which are included in the filter kit. Also, a small hose is attached to the kit, it is necessary for supplying air, therefore, its 1 end is attached to the hole on the filter nose, and the second comes out, it is possible to fix it on the upper edge of the aquarium wall using a special fastening. The main thing is that the air intake was made above the level of the aquarium water.

As a rule, on the nose of the internal filter, and some at the tip of the air hose has a regulator for air supply, which you can initially put in the middle position. During further operation, it will need to be adjusted as needed. Some of the aquarium fish love a fairly strong current, which is created by the filter, and some even can not stand it.

After the filter is installed and all its details are attached, you can connect it to the network. Further, all manipulations in the aquarium will need to be carried out only while the filter is turned off, since the device is not insured against damage, and this can lead to electric shock.

When the filter is set to a low flow of water, there may be no bubbles. If you can watch a wave of water in an aquarium, then the filter works well. Water is saturated with oxygen from the surface due to the waves.

How to install an external filter? The external filter is outside the aquarium. It does not clutter up the usable water space of the reservoir, does not bring resonance into the vividness and naturalness of the underwater landscape with unnecessary adaptations and details. Therefore, developers can create the most complex and super efficient filtration system that is not limited in volume.

Internal filter

Installing an external Tetra filter

AQUAEL FAN FILTER - Reliable and Efficient

INTERNAL FILTER FOR AQUARIUM. DISASSEMBLY, ASSEMBLING AND INSTALLING ON AN EXAMPLE OF ATMAN PF-400

Errors novice aquarists. Release 2

Aeration of the aquarium! Aquarium spray do it yourself!

BARBUS filter

Internal filter for aquarium - JEBO.

Overview and installation of the external filter Tetra EX 800

Pin
Send
Share
Send
Send